Don’t need a standard length camera strap? I’m also sharing a wristlet camera strap for those who like to travel light! There are so many great cotton yarns on the market, so it’s easier than ever to pick your favorite color. You can also stick with natural cotton if you prefer something really neutral. The best part is that if these get dirty, you can just throw them in the washing machine on a gentle cycle and it’ll be as good as new.
-over the door hook to anchor the clasp to while tying knots
NOTE: I used an over the door clothes hook and metal hoop that I hooked my clasp to for maximum comfort. You can also use an S-hook. The instructions below teach how to construct any of the three different camera strap lengths even though I am only showing how to construct the wristlet. Note that 2mm cord and 3mm cord will give you different outcomes in both width and length, so be sure to use the correct cord weight shared in the links above.
If you’re making the roughly 48″ camera strap, cut four 28.5″ strands of 3mm cotton cord and set the rest aside.
If you’re making the wristlet camera strap, cut four 9′ lengths of 2 mm cotton and set the rest aside.
Step Three: Repeat with the next three strands. Then split them apart so that four strands are on one side and four strands are on the other. I will refer to these as strands 1-8 from left to right. Even if they move around, I’ll still refer to them in the order that they rest in each step. For example, if strand two finds itself on the opposite side after a knot, if will no longer be strand two but strand seven.
Step Four: Use strand four to tie two half hitches around strand five so that they rest about 2.5″ from the clasp.
Step Five: Use strand three to tie two half hitches as well.
Step Six: Repeat with strands two and then one. Now split the strands in half again so that the first four on left are the new strands 1-4 and the four on the right are strands 5-8.
Step Seven: Use strand six to tie two half hitches around strand five.
Step Eight: Repeat with strands seven and then eight. This makes the top half of your diamond pattern.
Step Nine: Use strands and seven to tie a half knot over the middle strands (3-6). Don’t pull it too tightly.
Step Eleven: Use the new strand two to tie two half hitches around strand one. This will start the bottom part of your diamond.
Step Twelve: Use strand three to tie two half hitch knots and then strand four.
Step Thirteen: Use strand seven to tie two half hitch knots around strand eight and then follow them using strands six and five.
Step Fourteen: Use the new strand four to tie two half hitch knots over strand five to close the bottom of your diamond.
Step Fifteen: Use strands one and four to tie two half knots to form a square knot over strands two and three. Repeat with strands five and eight over strands six and seven.
Step Sixteen: Start on your next diamond by using strand four to tie two half hitch knots over strand five, then repeat with strands three, two and one.
Step Seventeen: Finish the other top half of your diamond and then use the new strands two and seven to tie a square knot around strands three through six. Then finish up the bottom of your diamond, add square knots on either side of your diamond, and start a new diamond. Repeat until you are about three inches short of your desired length.
Step Nineteen: You’ll be doubling the amount of lark’s head knots on this lobster clasp, so squeeze them together tightly.
Step Twenty: Use the cord that you set aside at the beginning and cut two 2′ strands. Make an upside down U-shape with one end of the two strands so that the U is slightly above the lark’s head knots. Then fold the strands again near the tails of the lark’s head knots so that they reach over the strap.
Step Twenty-One: Use the long end of those two straps to trap the U-shape on top of the strap and continue wrapping around all of them to create a wrapped knot.
Step Twenty-Two: Once you’re almost to the lark’s head knots, place the long end of your wrapped knot strands through your loop.
Step Twenty-Three: Pull down on the other end of the loop so that the U shape, along with the long end, disappear under the wraps.
Step Twenty-Four: Trim off both ends of the wrapped knot and then gently trim off the excess from the tail ends. Spread your wrapped knot down to cover the cut ends.
Step Twenty-Five: Add another wrapped knot to the other end of your strap. It won’t be quite as thick because there are half as many strands to wrap around, but it won’t be too noticeable. Attach both lobster clasps to the same ring hook on your camera for the wristlet version.
If you’re making the 40″ or 48″ version, you’ll follow all of the same directions above but will attach one lobster clasp to each side of your camera.
NOTE: These camera straps are sturdy if made according to the directions. Always test out your camera strap holding your camera over your bed before taking it out. Always check that your lobster clasps are securely attached to your camera before picking it up.