And after no luck finding a tiny loom to weave on I had to design my own (as you do!).
And here she is. Isn’t she a cutie! I have a few for sale in my Etsy shop if you would like one (
This tutorial uses the full loom which makes a weaving approx 10cm x 3.5cm.
I will be doing another tutorial soon to make an even teenier one suitable for a smaller dolls house.
YOU WILL NEED:
A tiny loom or make one out of stiff card with cuts in it (
Thin wool, yarn twine etc
Tapestry needle, smaller needle
Gather your supplies. We are going to warp the loom with your chosen colour. I am using pink embroidery floss (all 6 strands) Cut a length of 1 metre (40″). Tie a single knot around the left hand side of the loom as shown, then loop the thread around again and tuck the thread under so you end up with the thread secured but easy to undo at the end.
UPDATE: I have found a slightly quicker way to warp the Little Loom. Check out my quick video…
Start threading as shown up through the first gap, up to top, hook around and down. Continue in this way until you reach the end. When you reach the bottom right hold on tight to the thread with one hand and…
…with your other hand loop the loose thread around the right hand side of the loom, tying a loose knot as you did at the start with another loop around to secure it as before.
Your loom should look like this, all warped up and secure at each end. Thread your needle with same colour thread as the warp (6 strands) with a length of approx 50cm (20 inches). Start at one end of the loom and do an ‘over and under’ stitch ensuring you leave a tail of at least 10cm to the side of the loom which will be sewed into the back of the weave at the end. Push the row as far down as you can as on the loom as shown.
Do 3 or 4 rows in the same manner making sure in your return row that the ‘Over and under’ is opposite to the row below.
Next we are going to do a row of tassels.
Using the same thread (6 strands) cut 4 lengths at 17cm each for each tassel. Gather each group of 4 together then fold in half with finger between as shown.
Slot the folded threads under the first warp thread as shown, then feed tails through the loop and pull tight. Then slide down to sit on top of rows previously done.
Repeat the process for every warp strand. I decided to add 3 tassels of bright pink just off centre.
Here I did about 5 or 6 rows of over/under stitch. Again make sure you leave enough thread at the start of the row as you did before. Then I have added a couple more rows of light pink (6 strands). Then a row of a thin ribbon.
Carry on alternating rows of colours and textures. In the second photo I am adding a row of soumak. Cut a length of about 60cm and fold in half. Loop through as shown, tuck tails through loop. Now thread the two ends through the needle as shown and separate the ribbon by the first loop.
Now bring the needle up under next warp thread and pull through, and continue this process until you have a row. I find it easier to add this row higher up then fill in the weaving between otherwise it gets a bit fiddly.
I have filled in the gap with more rows of weaving and then a few more on top of the soumak. Don’t weave right to the top of your loom, leave a gap to insert your hanging rod. Now in photo 3 it is time to start taking your masterpiece off the loom. Lift up your tassel fringe as shown. Take this step nice and slowly, I highly recommend child free environment for this particular step! You will have 3 strands dangling down: 2 strands from the knots on either side and 1 strand from the first rows of weaving you did. Start with the latter and thread it on a needle.
Now just run it through a few stitches to keep it in place. It will be covered by the tassels so you don’t need be to be too particular. Trim the end. Now carefully untie the knots from either end.
Then carefully unhook the warp threads from the bottom pegs. Attach the left hand thread to the needle and carefully weave through the loops in an over and under fashion as if doing a row of weaving, then leave thread dangling. Do the same for the other end, weave it though and leave thread hanging.
Now we are going to make knots at either end by threading the needle though, making a loop and pulling thread through and pulling tight. Repeat at other end.
Trim threads. You will find by now your weaving has probably come off the top of the loom also. Don’t panic as it won’t go anywhere. Grab your dowel or stick and weave it though the top loops as if doing another row weaving of over/under. Now it is time to weave in all the ends. ENSURE you have FLIPPED your weaving to the BACK SIDE! It is easier to sew the ends in one at a time and has a much neater result. Thread up the first end…
…and catch in the top later of threads, pull through and trim. For a bulkier thread or ribbon which is too hard to weave in without it showing through to the front I just like to tie a loose knot at the back and trim, see photos 2 +3. Once you have woven in the ends it will look like photo 4. I decided to leave the soumak strands dangling as a feature.
Just about done. Flip it over to the right side and straighten out your tassels ready to trim. I have found my daughter’s my little pony comb is an excellent tassel detangler!!! Hang your weaving on a little nail and trim your fringe to a desired length and shape. I like to hang my weaving straight on a wee nail but you can always add a little hanging string to the top if you prefer.
So cute and so much fun to do. Great as a decorative wall hanging, dolls house feature or string it up and wear it as a necklace. So now I am off to keep playing with my little loom and to come up with some more fun ideas for you to try with yours.
As always if you have any questions please let me know.